Construction

CarboPur WFA was developed for application in mining, tunnelling, civil engineering and reconstruction of buildings.

CarboPur WFA is used for:

• Consolidation in dry,wet and water-bearing strata
• Sealing against strong water ingress (also seawater)
• Sealing against water under pressure e.g. from strata, dams or shaft walls
• Stabilization and sealing work in tunnels
• Repair of old shafts and tunnels
• Stabilization of crown abutments in tunnelling
• Sealing of anchoring of sheet pilings etc. in ground water and many other special applications

CarboStop 102 is a water-reactive one-component polyurethane resin. CarboStop 102 is CFC and solvent free.The reaction begins when the mix comes in contact with water.

• Stopping of water inflow under high pressure.
• Coagulation and water sealing of loose rock.
• Grouting of fine to grained sands.
• Fixing of anchors, self drilling anchors and cable bolts in sand under water transit
• Deep injection
• Injection of cracks, honeycombs, cold joints and non-moving joints.
• Injections of man-accessible sewer lines and tubes
• Injection in simultaneous or sequential stages during the cement grouting,(Carbo-Grouting System), and or for the automated compounded grouting, i.e., resin mixture + reactive, or non-reactive fillers for the filling of large voids under high water transit and pressure (Carbo-Block)

GeoFlex is flexible and under the stress of strata movement is capable of dissipating deformation energy. GeoFlex achieves its ultimate strength much faster than other resins, even when applied in thin layers, just a few minutes after application.   

CarboCryl SV is based on methacrylates and hardens to an elastic product. CarboCryl SV is characterized by its low mixing viscosity, which is similar to the viscosity of water. CarboCryl SV can be used for curtain grouting and ground stabilization.  

CarboCryl SV is not for use as a crack injection product, for that use CarboCryl HV. CarboCryl SV curing times can bed adjusted by varying the amount of B2, hardener, or alternatively B2L. 

CarboCryl SV does not contain any acryl amide.

CarboStop 102 is a water-reactive one-component polyurethane resin. CarboStop 102 is CFC and solvent free.The reaction begins when the mix comes in contact with water.

• Stopping of water inflow under high pressure.
• Coagulation and water sealing of loose rock.
• Grouting of fine to grained sands.
• Fixing of anchors, self drilling anchors and cable bolts in sand under water transit
• Deep injection
• Injection of cracks, honeycombs, cold joints and non-moving joints.
• Injections of man-accessible sewer lines and tubes
• Injection in simultaneous or sequential stages during the cement grouting,(Carbo-Grouting System), and or for the automated compounded grouting, i.e., resin mixture + reactive, or non-reactive fillers for the filling of large voids under high water transit and pressure (Carbo-Block)

GeoFlex is flexible and under the stress of strata movement is capable of dissipating deformation energy. GeoFlex achieves its ultimate strength much faster than other resins, even when applied in thin layers, just a few minutes after application.   

TekRok was developed in response to customer demand for a high-strength pumpable cement for underground construction projects such as belt drives, shop floors and sump holes etc. It was specifically designed for pumping through our placer unit. The placer meters and mixes the proper amounts of water and powder as it pumps the TekRok material. Fifty- four 50 pound bags of TekRok powder are used per cubic yard.

The cured TekRok cement is non-shrinking and dries to a durable, off-white finish. The material has a pumping life of up to 30 minutes, and sets in 5 to 8 hours. TekRok is especially suited for small to medium sized construction projects or for projects where the convenience of a pumpable factory blended cement mortar is required.

TekCrete Fast was developed in response to customer  demand for a shotcrete (gunite) with effectively immediate strength on application. TekCrete Fast may be used with or without steel or polymer mesh, although the use of mesh will provide additional tensile and flexural strength.

Fiber reinforced, this product offers superlative adhesion characteristics with typical compressive strengths over 11,000 psi. It is ideally suited for use where immediate structural strength is required.

Binding broken base material together for better structural integrity, TekCrete Fast can be used anywhere where conventional shotcrete (gunite) is used and with any coating or sealant. It performs best when applied as soon as possible after the base material is exposed. Including rebound, TekCrete Fast has a surface coverage of approximately 8.2 ft² per 60lb. bag at an application thickness of 1⁄2“.

TekCrete Fast was developed in response to customer  demand for a shotcrete (gunite) with effectively immediate strength on application. TekCrete Fast may be used with or without steel or polymer mesh, although the use of mesh will provide additional tensile and flexural strength.

Fiber reinforced, this product offers superlative adhesion characteristics with typical compressive strengths over 11,000 psi. It is ideally suited for use where immediate structural strength is required.

Binding broken base material together for better structural integrity, TekCrete Fast can be used anywhere where conventional shotcrete (gunite) is used and with any coating or sealant. It performs best when applied as soon as possible after the base material is exposed. Including rebound, TekCrete Fast has a surface coverage of approximately 8.2 ft² per 60lb. bag at an application thickness of 1⁄2“.

Tekcrete™ Pro 1500 is ideal for large vertical and overhead structural repairs where a rapid hardening product is needed.

Supplied as a ready to use dry powder, formulated for dry mix shotcrete requiring only the addition of water.

The controlled set feature allows 10-15 mins of working time for troweling if needed. Very high early and ultimate compressive strengths are achievable. Each 60 lb bag of TekCrete Pro 1500 contains approximately 0.45 cubic feet of material.

TekFlex® is safe to handle and apply using conventional systems and can be hand applied or mechanically applied. No specific ventilation requirements are necessary for the application with only conventional PPE required.

It has got a high polarity and is environmentally compatible. Not for applications with sodium silicate based components ( e.g. Carbothix Compt A, CarboLith Compt A etc), as CarboSolv D reacts with sodium silicate.

Cleanser for polyurethane applications, especially for flushing and cleaning pumps and hoses.

CarboSolv D is a degreasing agent, thus after contact with skin insure to proper clean with soap and water making sure to apply lotion to skin.

It is readily biodegradable. It is compatible with the standard sealing materials such as Viton, FPM, HBNR, AU, NBR.

Biodegradable lubricant for flushing and preserving injection pumps

Celbex 653 is a blend of water-soluble, high molecular-weight polymers supplied as a white powder.

It is designed to provide a stable polymer matrix enveloping every cement particle, which functions as a protective coating and thus prevents water washout.

WHY CARBOLITH PL?

CarboLith PL is used to repair sewer ducts and pipes and features excellent properties and economical advantages. The non-foaming elasticised resin hardens very well even in case of large volumes of external water inflow.

Component A of Carbolith PL is a water-glass component with additives. Component B is a modified polyisocyanate. Component C is a blend of additives improving the components and regulating the pot life of the mixture.The combination of components and liner forms an interpenetrating network of tough elastic, non-foamed silicate resin.

CarboPur resins production line offers high-quality materials for temporary or permanent applications with different reaction data and resin behavior, applicable in infrastructure and civil engineering.

These resins are applicable over a wide range of temperatures and act effectively even against pressurised water.

CarboPur WX is used for stabilisation in wet or water bearing rock formations. It is used for sealing water tributaries from rock formations, dams, or shaft walls. It can be used in renovation of wet shafts, tunnels, sewers, or brickwork.

CarboPur WS is used for curtain injection in tunnels, dams, or on shaft walls; sealing against water, stabilisation, consolidation and repairing of cracks &/or fissures.

CarboPur WFA is used for sealing strong water ingress, e.g.construction pits, pipelines, shafts, and tunnels.

These products are used for:

Grouting of fine to very fine hair line cracks and water-carrying sands or porous materials. Used for deep injecting, fixing of anchors, stabilisation and sealing of loose rock, stoppage of water inflow (also salt water), injecting of man-accessible sewer lines and tubes.

Stopping water inflow (also salt water), stabilisation and water sealing of loose rock, grouting of fine to medium-fine grained sands and gravel, fixing of anchors, injection of cracks, honeycombs, injections of man-accessible sewer lines and tubes

Stopping of water inflow (also salt water), sealing of loose rock, sealing of cracks and expansion joints in bridges and concrete structures. For use in deep injection, grouting of medium-fine to larger cracks, fissures, honeycombs, injections of man-accessible sewer lines and tubes where high elasticity and flexibility is required.

WHY CARBOLITH PL?

CarboLith PL is used to repair sewer ducts and pipes and features excellent properties and economical advantages. The non-foaming elasticised resin hardens very well even in case of large volumes of external water inflow.

Component A of Carbolith PL is a water-glass component with additives. Component B is a modified polyisocyanate. Component C is a blend of additives improving the components and regulating the pot life of the mixture.The combination of components and liner forms an interpenetrating network of tough elastic, non-foamed silicate resin.

CarboPur resins production line offers high-quality materials for temporary or permanent applications with different reaction data and resin behavior, applicable in infrastructure and civil engineering.

These resins are applicable over a wide range of temperatures and act effectively even against pressurised water.

CarboPur WX is used for stabilisation in wet or water bearing rock formations. It is used for sealing water tributaries from rock formations, dams, or shaft walls. It can be used in renovation of wet shafts, tunnels, sewers, or brickwork.

CarboPur WS is used for curtain injection in tunnels, dams, or on shaft walls; sealing against water, stabilisation, consolidation and repairing of cracks &/or fissures.

CarboPur WFA is used for sealing strong water ingress, e.g.construction pits, pipelines, shafts, and tunnels.

TekCrete Fast was developed in response to customer  demand for a shotcrete (gunite) with effectively immediate strength on application. TekCrete Fast may be used with or without steel or polymer mesh, although the use of mesh will provide additional tensile and flexural strength.

Fiber reinforced, this product offers superlative adhesion characteristics with typical compressive strengths over 11,000 psi. It is ideally suited for use where immediate structural strength is required.

Binding broken base material together for better structural integrity, TekCrete Fast can be used anywhere where conventional shotcrete (gunite) is used and with any coating or sealant. It performs best when applied as soon as possible after the base material is exposed. Including rebound, TekCrete Fast has a surface coverage of approximately 8.2 ft² per 60lb. bag at an application thickness of 1⁄2“.

TekFlex® is safe to handle and apply using conventional systems and can be hand applied or mechanically applied. No specific ventilation requirements are necessary for the application with only conventional PPE required.

TekCrete Fast was developed in response to customer  demand for a shotcrete (gunite) with effectively immediate strength on application. TekCrete Fast may be used with or without steel or polymer mesh, although the use of mesh will provide additional tensile and flexural strength.

Fiber reinforced, this product offers superlative adhesion characteristics with typical compressive strengths over 11,000 psi. It is ideally suited for use where immediate structural strength is required.

Binding broken base material together for better structural integrity, TekCrete Fast can be used anywhere where conventional shotcrete (gunite) is used and with any coating or sealant. It performs best when applied as soon as possible after the base material is exposed. Including rebound, TekCrete Fast has a surface coverage of approximately 8.2 ft² per 60lb. bag at an application thickness of 1⁄2“.

Tekcrete™ Pro 1500 is ideal for large vertical and overhead structural repairs where a rapid hardening product is needed.

Supplied as a ready to use dry powder, formulated for dry mix shotcrete requiring only the addition of water.

The controlled set feature allows 10-15 mins of working time for troweling if needed. Very high early and ultimate compressive strengths are achievable. Each 60 lb bag of TekCrete Pro 1500 contains approximately 0.45 cubic feet of material.

It has got a high polarity and is environmentally compatible. Not for applications with sodium silicate based components ( e.g. Carbothix Compt A, CarboLith Compt A etc), as CarboSolv D reacts with sodium silicate.

Cleanser for polyurethane applications, especially for flushing and cleaning pumps and hoses.

CarboSolv D is a degreasing agent, thus after contact with skin insure to proper clean with soap and water making sure to apply lotion to skin.

It is readily biodegradable. It is compatible with the standard sealing materials such as Viton, FPM, HBNR, AU, NBR.

Biodegradable lubricant for flushing and preserving injection pumps

Celbex 653 is a blend of water-soluble, high molecular-weight polymers supplied as a white powder.

It is designed to provide a stable polymer matrix enveloping every cement particle, which functions as a protective coating and thus prevents water washout.

Minova EXRB consists of a folded steel tube with upper bushing and inflation bushing welded at each end of the tube. A specially designed adjustable face plate is delivered as an option.

EXRBs require steel that has extremely good elongation and form-ability properties. This quality produces a finished bolt that accommodates large rock movements and still maintains its high load bearing capacity. EXRBs deliver a high level of safety and uninterrupted production in the customer’s operations.

Celroc P is a high-strength, non-shrink, non-metallic grout consisting of rapid hardening hydraulic cement and super plasticizer. Designed to produce a pumpable grout at low w/c ratios with the unique features of being highly resistant to dilution in moving water and aggressive ground conditions.

These products were designed to improve the productivity of ground support installation in underground mining and tunnelling applications. Using the pumpable resin enables the load to be taken up in minutes rather than the typical 24 hours from cementitious grouted systems.

CarboThix™ Fast

CarboThix™ Fast is an immediate partially stiffening and very fast curing dual component silicate resin for bonding injection drilling anchors, also for rock stabilization and water sealing. CarboThix Fast was developed to improve the productivity of ground support installation in underground mining and tunnelling applications. Using the pumpable resin enables loads to be taken up in minutes rather than the typical 24 hours from cementitious grouted systems. Typical applications of CarboThix Fast include grouting of cable bolts, steel or GFRP bolts, and sealing of roof bolts.

CarboThix™ 2

Typical applications of CarboThix™ 2 include sealing of injection bolts, steel or GFRP rods, and sealing of roof bolts. During application, the two components are intimately mixed and achieve a grease-like viscosity (the so called Thix effect) so that the grout stops flowing and cures to form a tough elastic and non-porous resin that will not mix with water or be diluted in wet holes.

TekCrete Fast was developed in response to customer  demand for a shotcrete (gunite) with effectively immediate strength on application. TekCrete Fast may be used with or without steel or polymer mesh, although the use of mesh will provide additional tensile and flexural strength.

Fiber reinforced, this product offers superlative adhesion characteristics with typical compressive strengths over 11,000 psi. It is ideally suited for use where immediate structural strength is required.

Binding broken base material together for better structural integrity, TekCrete Fast can be used anywhere where conventional shotcrete (gunite) is used and with any coating or sealant. It performs best when applied as soon as possible after the base material is exposed. Including rebound, TekCrete Fast has a surface coverage of approximately 8.2 ft² per 60lb. bag at an application thickness of 1⁄2“.

TekCrete Fast was developed in response to customer  demand for a shotcrete (gunite) with effectively immediate strength on application. TekCrete Fast may be used with or without steel or polymer mesh, although the use of mesh will provide additional tensile and flexural strength.

Fiber reinforced, this product offers superlative adhesion characteristics with typical compressive strengths over 11,000 psi. It is ideally suited for use where immediate structural strength is required.

Binding broken base material together for better structural integrity, TekCrete Fast can be used anywhere where conventional shotcrete (gunite) is used and with any coating or sealant. It performs best when applied as soon as possible after the base material is exposed. Including rebound, TekCrete Fast has a surface coverage of approximately 8.2 ft² per 60lb. bag at an application thickness of 1⁄2“.

Celroc P is a high-strength, non-shrink, non-metallic grout consisting of rapid hardening hydraulic cement and super plasticizer. Designed to produce a pumpable grout at low w/c ratios with the unique features of being highly resistant to dilution in moving water and aggressive ground conditions.

They are suitable for temporary and permanent solutions and with their low-weight, their are ideal for decreasing risks associated with manual handling.

Strategic partnership

Our partnership with FiReP® allows us to provide you with the flexibility that you need, wherever you are.

FiReP® Group is one of the world’s largest producer of Fibre Reinforced Polymer (FRP) pultruded bars with unique profiles and thread functions for application in the mining, construction and energy sectors.

The Group has two plants in Shanghai (China) and Velenje (Slovenia), certified according to ISO9001 and ISO14001.

With subsidiaries in the 6 countries Switzerland, Germany, China, Slovenia, Canada and Japan the group offers worldwide presence and service on site.

Minova has partnered with FiReP in 2009 to bring new products and technical expertise to our portfolio.

Since then, we have been working jointly to provide our mining, energy and construction customers with an enhanced portfolio of support products and services.

CarboPur resins production line offers high-quality materials for temporary or permanent applications with different reaction data and resin behavior, applicable in infrastructure and civil engineering.

These resins are applicable over a wide range of temperatures and act effectively even against pressurised water.

CarboPur WX is used for stabilisation in wet or water bearing rock formations. It is used for sealing water tributaries from rock formations, dams, or shaft walls. It can be used in renovation of wet shafts, tunnels, sewers, or brickwork.

CarboPur WS is used for curtain injection in tunnels, dams, or on shaft walls; sealing against water, stabilisation, consolidation and repairing of cracks &/or fissures.

CarboPur WFA is used for sealing strong water ingress, e.g.construction pits, pipelines, shafts, and tunnels.

These products are used for:

Grouting of fine to very fine hair line cracks and water-carrying sands or porous materials. Used for deep injecting, fixing of anchors, stabilisation and sealing of loose rock, stoppage of water inflow (also salt water), injecting of man-accessible sewer lines and tubes.

Stopping water inflow (also salt water), stabilisation and water sealing of loose rock, grouting of fine to medium-fine grained sands and gravel, fixing of anchors, injection of cracks, honeycombs, injections of man-accessible sewer lines and tubes

Stopping of water inflow (also salt water), sealing of loose rock, sealing of cracks and expansion joints in bridges and concrete structures. For use in deep injection, grouting of medium-fine to larger cracks, fissures, honeycombs, injections of man-accessible sewer lines and tubes where high elasticity and flexibility is required.

They are suitable for temporary and permanent solutions and with their low-weight, their are ideal for decreasing risks associated with manual handling.

Strategic partnership

Our partnership with FiReP® allows us to provide you with the flexibility that you need, wherever you are.

FiReP® Group is one of the world’s largest producer of Fibre Reinforced Polymer (FRP) pultruded bars with unique profiles and thread functions for application in the mining, construction and energy sectors.

The Group has two plants in Shanghai (China) and Velenje (Slovenia), certified according to ISO9001 and ISO14001.

With subsidiaries in the 6 countries Switzerland, Germany, China, Slovenia, Canada and Japan the group offers worldwide presence and service on site.

Minova has partnered with FiReP in 2009 to bring new products and technical expertise to our portfolio.

Since then, we have been working jointly to provide our mining, energy and construction customers with an enhanced portfolio of support products and services.

TekCrete Fast was developed in response to customer  demand for a shotcrete (gunite) with effectively immediate strength on application. TekCrete Fast may be used with or without steel or polymer mesh, although the use of mesh will provide additional tensile and flexural strength.

Fiber reinforced, this product offers superlative adhesion characteristics with typical compressive strengths over 11,000 psi. It is ideally suited for use where immediate structural strength is required.

Binding broken base material together for better structural integrity, TekCrete Fast can be used anywhere where conventional shotcrete (gunite) is used and with any coating or sealant. It performs best when applied as soon as possible after the base material is exposed. Including rebound, TekCrete Fast has a surface coverage of approximately 8.2 ft² per 60lb. bag at an application thickness of 1⁄2“.

Tekcrete™ Pro 1500 is ideal for large vertical and overhead structural repairs where a rapid hardening product is needed.

Supplied as a ready to use dry powder, formulated for dry mix shotcrete requiring only the addition of water.

The controlled set feature allows 10-15 mins of working time for troweling if needed. Very high early and ultimate compressive strengths are achievable. Each 60 lb bag of TekCrete Pro 1500 contains approximately 0.45 cubic feet of material.

TekFlex® is safe to handle and apply using conventional systems and can be hand applied or mechanically applied. No specific ventilation requirements are necessary for the application with only conventional PPE required.

RD10 is environmentally friendly and can be applied through either topical means or mixed in with the soil.

The control of dust, typically by the topical application of water, can be a costly and disruptive process – often effective for only a limited time period.

RD10 is a water soluble non-hazardous emulsion that is designed specifically for:

• Dust Suppression
• Erosion control – stock piles
• Soil solidification and stabilization

The application of RD10 is completed by adding a percentage of the product to the water being used to control dust. Any water source can be used as the water is simply a carrier for the RD10 agent. Depending on the application, various rates of RD10 can be used.

TekRok Pro 2500 is a specially formulated mix and pour repair cement contains a unique blend of cements, additives and carefully graded aggregates. It is superbly designed for the immediate repair of roads and other horizontal construction repair projects. It has a functional working pot life of 10–15 mins before it starts to react, thus reducing the amount of time required to finish patch and repair projects.

Each 50 lbs bag of TekRok Pro 2500 contains approximately 0.4 cubic feet of material.

It has got a high polarity and is environmentally compatible. Not for applications with sodium silicate based components ( e.g. Carbothix Compt A, CarboLith Compt A etc), as CarboSolv D reacts with sodium silicate.

Cleanser for polyurethane applications, especially for flushing and cleaning pumps and hoses.

CarboSolv D is a degreasing agent, thus after contact with skin insure to proper clean with soap and water making sure to apply lotion to skin.

It is readily biodegradable. It is compatible with the standard sealing materials such as Viton, FPM, HBNR, AU, NBR.

Biodegradable lubricant for flushing and preserving injection pumps

Celbex 653 is a blend of water-soluble, high molecular-weight polymers supplied as a white powder.

It is designed to provide a stable polymer matrix enveloping every cement particle, which functions as a protective coating and thus prevents water washout.

CarboPur resins production line offers high-quality materials for temporary or permanent applications with different reaction data and resin behavior, applicable in infrastructure and civil engineering.

These resins are applicable over a wide range of temperatures and act effectively even against pressurised water.

CarboPur WX is used for stabilisation in wet or water bearing rock formations. It is used for sealing water tributaries from rock formations, dams, or shaft walls. It can be used in renovation of wet shafts, tunnels, sewers, or brickwork.

CarboPur WS is used for curtain injection in tunnels, dams, or on shaft walls; sealing against water, stabilisation, consolidation and repairing of cracks &/or fissures.

CarboPur WFA is used for sealing strong water ingress, e.g.construction pits, pipelines, shafts, and tunnels.

These products are used for:

Grouting of fine to very fine hair line cracks and water-carrying sands or porous materials. Used for deep injecting, fixing of anchors, stabilisation and sealing of loose rock, stoppage of water inflow (also salt water), injecting of man-accessible sewer lines and tubes.

Stopping water inflow (also salt water), stabilisation and water sealing of loose rock, grouting of fine to medium-fine grained sands and gravel, fixing of anchors, injection of cracks, honeycombs, injections of man-accessible sewer lines and tubes

Stopping of water inflow (also salt water), sealing of loose rock, sealing of cracks and expansion joints in bridges and concrete structures. For use in deep injection, grouting of medium-fine to larger cracks, fissures, honeycombs, injections of man-accessible sewer lines and tubes where high elasticity and flexibility is required.

TekCrete Fast was developed in response to customer  demand for a shotcrete (gunite) with effectively immediate strength on application. TekCrete Fast may be used with or without steel or polymer mesh, although the use of mesh will provide additional tensile and flexural strength.

Fiber reinforced, this product offers superlative adhesion characteristics with typical compressive strengths over 11,000 psi. It is ideally suited for use where immediate structural strength is required.

Binding broken base material together for better structural integrity, TekCrete Fast can be used anywhere where conventional shotcrete (gunite) is used and with any coating or sealant. It performs best when applied as soon as possible after the base material is exposed. Including rebound, TekCrete Fast has a surface coverage of approximately 8.2 ft² per 60lb. bag at an application thickness of 1⁄2“.

Tekcrete™ Pro 1500 is ideal for large vertical and overhead structural repairs where a rapid hardening product is needed.

Supplied as a ready to use dry powder, formulated for dry mix shotcrete requiring only the addition of water.

The controlled set feature allows 10-15 mins of working time for troweling if needed. Very high early and ultimate compressive strengths are achievable. Each 60 lb bag of TekCrete Pro 1500 contains approximately 0.45 cubic feet of material.

TekFlex® is safe to handle and apply using conventional systems and can be hand applied or mechanically applied. No specific ventilation requirements are necessary for the application with only conventional PPE required.

CarboPur resins production line offers high-quality materials for temporary or permanent applications with different reaction data and resin behavior, applicable in infrastructure and civil engineering.

These resins are applicable over a wide range of temperatures and act effectively even against pressurised water.

CarboPur WX is used for stabilisation in wet or water bearing rock formations. It is used for sealing water tributaries from rock formations, dams, or shaft walls. It can be used in renovation of wet shafts, tunnels, sewers, or brickwork.

CarboPur WS is used for curtain injection in tunnels, dams, or on shaft walls; sealing against water, stabilisation, consolidation and repairing of cracks &/or fissures.

CarboPur WFA is used for sealing strong water ingress, e.g.construction pits, pipelines, shafts, and tunnels.

These products are used for:

Grouting of fine to very fine hair line cracks and water-carrying sands or porous materials. Used for deep injecting, fixing of anchors, stabilisation and sealing of loose rock, stoppage of water inflow (also salt water), injecting of man-accessible sewer lines and tubes.

Stopping water inflow (also salt water), stabilisation and water sealing of loose rock, grouting of fine to medium-fine grained sands and gravel, fixing of anchors, injection of cracks, honeycombs, injections of man-accessible sewer lines and tubes

Stopping of water inflow (also salt water), sealing of loose rock, sealing of cracks and expansion joints in bridges and concrete structures. For use in deep injection, grouting of medium-fine to larger cracks, fissures, honeycombs, injections of man-accessible sewer lines and tubes where high elasticity and flexibility is required.

It is readily biodegradable. It is compatible with the standard sealing materials such as Viton, FPM, HBNR, AU, NBR.

Biodegradable lubricant for flushing and preserving injection pumps

Celbex 653 is a blend of water-soluble, high molecular-weight polymers supplied as a white powder.

It is designed to provide a stable polymer matrix enveloping every cement particle, which functions as a protective coating and thus prevents water washout.

GeoFoam is flame-resistant easily cuttable by tunnel boring machines when cured and has a low exothermic temperature making it safer for installers to use and the environment.

It is designed for the immediate stabilization of unconsolidated geological formations during tunneling, drilling, mining and other civil engineering projects.

After mixing, the resin quickly starts foaming-up within seconds forming a strong lightweight foam. Common uses include structural support in tunnelling and for the lifting of roadways or slabs.

TekFoam is a non-combustible, void-filling, structural cement foam. Supplied as a powder, the cement forms a low-density foam (0.25 to 0.35 sg) when combined with the proper amount of air and water in the specially designed Tekplacer unit.

TekFoam mix is typically pumped 400 feet (121.9m) through a 1” (25.4mm) diameter hose, farther through a larger diameter hose. The 20 psi (0.1379MPa) product begins to gel in minutes, forming a non-toxic, non-combustible product weighing approximately 540 lbs/ yd3 (320.4kg/ m3).  Because of its rapid strength gain, the foam material is firm enough to walk on in 30 to 60 minutes.

It has got a high polarity and is environmentally compatible. Not for applications with sodium silicate based components ( e.g. Carbothix Compt A, CarboLith Compt A etc), as CarboSolv D reacts with sodium silicate.

Cleanser for polyurethane applications, especially for flushing and cleaning pumps and hoses.

CarboSolv D is a degreasing agent, thus after contact with skin insure to proper clean with soap and water making sure to apply lotion to skin.

It is readily biodegradable. It is compatible with the standard sealing materials such as Viton, FPM, HBNR, AU, NBR.

Biodegradable lubricant for flushing and preserving injection pumps

Celbex 653 is a blend of water-soluble, high molecular-weight polymers supplied as a white powder.

It is designed to provide a stable polymer matrix enveloping every cement particle, which functions as a protective coating and thus prevents water washout.